- HOME ABOUT US PRIVACY STATEMENT COMPANIES WE CARRY
- INTERNATIONAL SHIPPING AGREEMENT MUST BE INITIALED BEFORE SHIPPING
- WhanAB VW Audi Cast aluminum flanges Passat B5 VW 1.8 2.0 engines many more
- Sensors for VW and Audi... Thermostat & Radiator Fan Switch
- WhanAB 1.8t Cast Aluminum Coolant Kit for VW Audi Seat Skoda 1.8t engines
- WhanAB TT MK1 Interior /Trans./CAP's OEM and CUP HOLDERS VW MK4
- WHANAB DIPSTICK "RING" AND HANDLE
- WhanAB 1.8t Dipstick tube / Top with "Ring" / Ends / Clamp in High Polish and Raw Aluminium. Directions.
- WhanAB "Ring" and Handle DIY
- WhanAB DIPSTICK TUBES for SALE
- WHANAB "ENGINE CAPS"
- 42DD Products
- Airbagged Trailers
- AIRLIFT Quote
- CIPHER AUTO SEAT RACING ORDER ON LINE
- ECOHITCH by TORKLIFT +++
- FORGE MOTOR SPORTS
- HPA\\\ Motorsports
- INTEGRATED ENGINEERING QUOTES
- JHMotor Sports
- KLUTCH REPUBLIK WHEEL QUOTE
- POWERFLEX PRODUCTS HOW TO ORDER
- SOLO-WERKS Order Online Free Shipping
- SOUTH BEND CLUTCH GOING ON
- STERN PRODUCTS BUY HERE
- VISRACING PAGE USE FORM FOR QUOTE
- V-MAXX SPECIAL GOING ON BRAKES
- WhanAB Retailer Recommendations
- DIY for AUDI
- DIY for VW
WhanAB Dipstick Tops fit any and all Dipsticks that have the Dipstick wire or flat metal that extends 5/16 above base of Dipstick handle Now Tube and clamp for 1.8t Audi TT MK1 Seat Leon Cupra MK1 VW MK4's Full Dipsticks Purchase from UROtuning or Gruvenparts

New dipstick handle and “Ring” which allows us to attach our handle to virtually any dipstick that is of round wire or slated stick metal that extends past the base of the handle…. The “Ring” is threaded and allows us to make many different designs as they are interchangeable. Order # WAB-44444 MSRP: $34.99
We will have more videos and DIY’s to show how to apply this to one’s own dipstick.
All in USD. Shipping is FREE in USA. International may buy but will be emailed for additional shipping charges.
DIPSTICK REPLACEMENT INSTRUCTIONS
Patent Pending
Tools needed dremal with cutting blade (cut handle off), your dipstick.
IMPORTANT WHEN YOU PULL YOUR DIPSTICK OUT: ONE WIPE IT OFF AND THE OTHER PUT A PIECE OF TAPE TO COVER THE OPENING "I USED PAINTERS TAPE "BLUE" *Your epoxy. Purchased or gift dipstick replacement handle.*Loctite GO2 Gel UPC #079340647763 is what WhanAB suggest
Cut your dipstick 1/4 inch left & right of center stem as the metal strip goes almost a full inch as shown here It should look like this Picture #1 then cut and stripe off plastic and do not cut the metal. "Clear all the plastic off and show only the metal ". Then smooth the base around the bottom of where the metal comes out. Put "Ring" over and thru wire or flat metal and cut off right at the top of the "Ring" Apply *epoxy on base of dipistick (in between "Orange" and "Ring") press down and apply epoxy in hole on top where wire or flat metal comes out.... Tighten both set screws.
We suggest to wait 24 hours before screwing on handle to the "Ring"
Any Questions: www.WhanAB.com
Video coming on and for DIY...
Product application, fitment and performance are the responsibility of person or persons applying purchased or gift product.
Order # WAB-44444 MSRP: $44.99 for High Polished
..................................... out of stock ............................
We will have more videos and DIY’s to show how to apply this to one’s own dipstick.
All in USD. Shipping is FREE in USA. International may buy but will be emailed for additional shipping charges.
DIPSTICK REPLACEMENT INSTRUCTIONS
Patent Pending
Tools needed dremal with cutting blade (cut handle off), your dipstick.
IMPORTANT WHEN YOU PULL YOUR DIPSTICK OUT: ONE WIPE IT OFF AND THE OTHER PUT A PIECE OF TAPE TO COVER THE OPENING "I USED PAINTERS TAPE "BLUE" *Your epoxy. Purchased or gift dipstick replacement handle.*Loctite GO2 Gel UPC #079340647763 is what WhanAB suggest
Cut your dipstick 1/4 inch left & right of center stem as the metal strip goes almost a full inch as shown here It should look like this Picture #1 then cut and stripe off plastic and do not cut the metal. "Clear all the plastic off and show only the metal ". Then smooth the base around the bottom of where the metal comes out. Put "Ring" over and thru wire or flat metal and cut off right at the top of the "Ring" Apply *epoxy on base of dipistick (in between "Orange" and "Ring") press down and apply epoxy in hole on top where wire or flat metal comes out.... Tighten both set screws.
We suggest to wait 24 hours before screwing on handle to the "Ring"
Any Questions: www.WhanAB.com
Video coming on and for DIY...
Product application, fitment and performance are the responsibility of person or persons applying purchased or gift product.
Order # WAB-44444 MSRP: $44.99 for High Polished
..................................... out of stock ............................
http://www.urotuning.com/Billet-Aluminum-Oil-Dipstick-Handle-One-size-fit-p/wab-44444.htm
http://www.gruvenparts.com/content/PDF/Dipstick_DIY.pdf
http://www.gruvenparts.com/content/PDF/Dipstick_DIY.pdf

New dipstick handle and “Ring” which allows us to attach our handle to virtually any dipstick that is of round wire or slated stick metal that extends past the base of the handle….
WAB-44444A Price $39.99 Out of Stock
WAB-44444A Price $39.99 Out of Stock

We have done almost the same thing for our 1.8t full dipstick tube / clamp / and end pieces as well. Order # WAB-44455
Price $99.99
OUT of STOCK
available here
Email: Gurbinder_1@hotmail.com He was in stock as of 03/07/2022
The video below is from 2011 as we are updating our video vault
Price $99.99
OUT of STOCK
available here
Email: Gurbinder_1@hotmail.com He was in stock as of 03/07/2022
The video below is from 2011 as we are updating our video vault

We have done almost the same thing for our 1.8t full dipstick in High Polish tube / clamp / and end pieces as well. Order # WAB-44455A
Price $119.99
OUT of STOCK
Price $119.99
OUT of STOCK
Here are other types of dipstick handles (Below Video) we have been selling in the past as well... The long handle dipstick for many VW MK3 VR6 will be ready end 2015 and will fit the "Ring" as well... also engine bay has been changed from other video from above...